Simply insert the Veet wax refill into the device. Place the plugged device on its base and leave it connected for 20min. You are now ready for your depilation session! To see the full instructions for use, please refer to the leaflet inside this pack. Waxing legs & arms: 1. To heat the wax, use only the Veet device. Insert the Veet wax refill into the device. Ensure it is fully inserted into the device. 2. Plug the electrical cable into the device and in the socket. The red light turns on to confirm the device is heating. Place the plugged device on its base and leave it connected for 20min. After 20min the wax is ready for application. Start to apply the wax to a small area first, to check that the wax applies easily. If the wax does not easily roll onto the skin, let the device warm the wax for at least an additional 5min. The wax is ready when it glides out of the roller easily and applies evenly to the skin. Do not allow the wax to come into contact with water as it would become ineffective. 3. Apply the wax in the direction of hair growth (from knee to ankle for legs). Check that the slanted side of the roller head is in contact with the skin during application to allow the roller to glide over the skin. 4. Immediately place the strip over the layer of wax, ensuring that there is at least 1cm at the bottom which is wax free. Rub the strip repeatedly over the wax in the direction of the hair growth. 5. Hold your skin taut to avoid discomfort. Holding the bottom of the strip, very quickly and in one swift motion, pull the strip back on itself against the direction your hair grows (from ankle to knee for legs) keeping the strip as close to the skin as possible. The FASTER you remove the strip the more effective it will be. 6. When you have finished waxing, remove any wax residues from your skin with a perfect finish wipe (you can alternatively use the back of a used strip). This wax cannot be rinsed off with water. 7. Unplug the device. After use the refill will be hot - Allow it to cool down before removing the refill from the device. If necessary, you can clean the roller head using the back of a used strip. Never use water, the Veet Finish wipes or any other liquid to clean the device & roller head. Replace the cap on the roll-on and store. Always store in a dry location. Do not wrap the power lead around the appliance, pull or twist the power lead. Waxing underarm: 1. To heat the wax, use only the Veet device. Insert the Veet wax refill into the device. Ensure it is fully inserted into the device. To wax your underarm, we recommend you to use the specifically designed Veet wax refill with a smaller roll-on head. 2. Plug the electrical cable into the device and in the socket. The red light turns on to confirm the device is heating. Place the plugged device on its base and leave it connected for 20min. After 20min the wax is ready for application. Start to apply the wax to a small area first, to check that the wax applies easily. If the wax does not easily roll onto the skin, let the device warm the wax for at least an additional 5min. The wax is ready when it glides out of the roller easily and applies evenly to the skin. Do not allow the wax to come into contact with water as it would become ineffective. 3. Your underarm hair grows in 2 directions so make sure you wax this area in 2 stages. Cut the strip to a suitable size. Put one hand behind your head and stretch your arm back to hold the skin taut. For the upper part of the underarm apply the wax by rolling up away from the centre of the underarm. For the lower part of the underarm apply the wax by rolling it down from the centre of the underarm. 4. Immediately place the strip onto one half of the underarm and rub repeatedly over the wax in the direction your hair grows (away from the centre of the underarm). 5. Very quickly and in one swift motion, pull the strip back on itself against the direction your hair grows keeping the strip as close to the skin as possible. The FASTER you remove the strip the more effective it will be. For the top half, remove strip downwards towards the centre of your underarm. For the bottom half, remove strip upwards towards the centre of the underarm. 6. When you have finished waxing, remove any wax residues from your skin with a perfect finish wipe (you can alternatively use the back of a used strip). This wax cannot be rinsed off with water. 7. Unplug the device. After use the refill will be hot - Allow it to cool down before removing the refill from the device. If necessary, you can clean the roller head using the back of a used strip. Never use water, the Veet Finish wipes or any other liquid to clean the device & roller head. Replace the cap on the roll-on and store. Always store in a dry location. Do not wrap the power lead around the appliance, pull or twist the power lead. Waxing bikini: 1. To heat the wax, use only the veet device. Insert the Veet wax refill into the device. Ensure it is fully inserted into the device. To wax your bikini line, we recommend you to use the specifically designed Veet wax refill with a smaller roll-on head. 2. Plug the electrical cable into the device and in the socket. The red light turns on to confirm the device is heating. Place the plugged device on its base and leave it connected for 20min. After 20min the wax is ready for application. Start to apply the wax to a small area first, to check that the wax applies easily. If the wax does not easily roll onto the skin, let the device warm the wax for at least an additional 5min. The wax is ready when it glides out of the roller easily and applies evenly to the skin. Do not allow the wax to come into contact with water as it would become ineffective. 3. Cut the strip to a suitable size for the area of your bikini line you want to wax. Bend your leg outwards. Hold the skin taut and apply the wax in the direction of hair growth. Only use on small areas at a time. 4. Immediately place a strip on your skin and rub repeatedly over the wax in the direction of your hair grows. 5. Hold your skin taut to avoid discomfort then very quickly and in one swift motion, pull the strip back on itself against the direction your hair grows keeping the strip as close to the skin as possible. The faster you remove the strip the more effective it will be. 6. When you have finished waxing, remove any wax residues from your skin with a perfect finish wipe (you can alternatively use the back of a used strip). This wax cannot be rinsed off with water. 7. Unplug the device. After use the refill will be hot - Allow it to cool down before removing the refill from the device. If necessary, you can clean the roller head using the back of a used strip. Never use water, the Veet Finish wipes or any other liquid to clean the device & roller head. Replace the cap on the roll-on and store. Always store in a dry location. Do not wrap the power lead around the appliance, pull or twist the power lead.
Suitable For: For all skin types.
